Indicator WIN7
Download PDF datasheet
Gicam weight indicators are weight indicator devices connected to load cells. We have multifunction displayers for weighing and dosing, for bridge weighing, with load limiter. Portable displayers are available in comfortable briefcases. We have panel mounting, portable, DIN and OMEGA bar mounts, analog indicators and touch screens indicators. IP65 products are available with dust protection. Gicam indicators support industrial communication protocols like PROFIBUS, PROFINET, MODBUS and more.
Indicator
Click on the image to enlarge
Technical specifications
| Power supply | Battery 6 V dc, external power supply 230 V ac , 7.5 V dc |
|---|---|
| Max power consumption | 5 W |
| Isolation | Class III |
| Operating temperature | -10 / +40°C (14 °F / 104°F) Humidity maximum 85% non-condensing |
| Storage temperature | -20 / +50°C (-4 / +122°F) |
| Display | Numeric 5-digit, 7-segment LED (h 20 mm) |
| Led | 3 3 mm indicator LEDs |
| Keyboard | 4 mechanical keys |
| Overall dimensions | 160 mm x 95 mm x 60 mm /6.30 x 3.74 x 2.36 in (l x h x p) |
| Case material | ABS |
| Protection level | IP 40 |
| Connections | Circular connector power supply. 9-pole SUB-D tubular connectors |
| Power supply load cells | 5 V dc / 60 mA (maximum 4 cells with 350 Ω in parallel) protected against short-circuit |
| Input sensitivity | 0.1 µV min |
| Linearity | < 0.01% of full scale |
| Temperature deviation | < 0.001% of full scale/C° |
| Internal resolution | 24 bit |
| Weight resolution | Up to 60,000 divisions (6,000 if metric divisions) |
| Measuring range | -0.5 / +3.5 mV/V |
| Weight acquisition frequency | 6 Hz - 25 Hz |
| Digital filter | 0.5 Hz – 5 Hz, selectable |
| Number of weight decimals | From 0 to 3 decimals |
| Zero / FS Calibration | Executable through buttons |
| Serial port | RS232c |
| Max. cable length | 15 m |
| Serial protocols | ASCII |
| Baud rate | 9600 bit/s |
| Program code memory | 64 Kbytes FLASH on board reprogrammable by RS232 |
| Data memory | 2 Kbytes |
| Optional fiscal memory | 1 Mbytes (up to 160.000 savings) |
| Conforms to standards | Compliance to norms EN61000-6-2, EN61000-6-3, EN45501, EN60950 |
For complete and up-to-date technical specifications please refer to the datasheet you can download here
Download PDF datasheet Connections
| Type | Connector J1 9P female SUB-D (cell) |
|---|---|
| Length | ND |
| 1 | Shield |
| 2 | + Power Supply |
| 3 | + Signal |
| 4 | - Signal |
| 5 | + Reference |
| 6 | - Reference |
| 7 | - Power supply |
| Type | Connector J2 9P male SUB-D (RS232) |
|---|---|
| Length | ND |
| 1 | NC |
| 2 | RX |
| 3 | TX |
| 4 | NC |
| 5 | GND |
| 6 | NC |
| 7 | NC |
| Type | Connector J3 |
|---|---|
| Length | ND |
| 1 | - Power Supply |
| 2 | + 7,5 V |
Load cell mounting
General guidelines for installing and mounting load cells:
- Respect the direction in which forces are applied to the load cells
- Do not exceed the temperature limits shown on the rating plate
- Do not remove the labels from the cells
- Protect cables properly with sheaths or cable ducts
- Connect each cell to earth with a suitable cable, bridging the plates of the mounting accessories if necessary
- Do not weld on the mechanical structure once the cells are in place
- Avoid or minimise mechanical constraints between the fixed structure and the weighed structure, to prevent weighing errors and zero return problems
- When vibrations or dynamic loads are present, protect the cells with anti-vibration mounts
- Protect the cells from dust build-up with suitable covers