Indicator LIM 60 HA
Download PDF datasheet
Gicam weight indicators are weight indicator devices connected to load cells. We have multifunction displayers for weighing and dosing, for bridge weighing, with load limiter. Portable displayers are available in comfortable briefcases. We have panel mounting, portable, DIN and OMEGA bar mounts, analog indicators and touch screens indicators. IP65 products are available with dust protection. Gicam indicators support industrial communication protocols like PROFIBUS, PROFINET, MODBUS and more.
LOAD LIMITER for load cells
Click on the image to enlarge
Technical specifications
| Power supply | 230 V ac (optional 115 V ac e 24 V cc) – 50 / 60 Hz |
|---|---|
| Max power consumption | 10 W |
| Operating temperature | -10 / +40°C (14 °F / 104°F) Humidity maximum 85% non-condensing |
| Storage temperature | -20 / +50°C (-4 / +122°F) |
| Display | High efficiency 6-digit numerical LED and wide viewing angle, reading distance up to 50 feet |
| Visualized data | Weight acquired from cells or analogue input 0-10V/4-20 mA, alphanumeric indications/programming menu |
| Overall dimensions | 320 x 110 x 90 mm /12.6 x 4.3 x 3.5 in (l x h x p) |
| Mounting | Wall-mounted with 4 external side holes Ø 6 mm with center distance 340 x 80 mm (l x h) |
| Protection level | IP 65 |
| Connections | Waterproof circular connectors with conductor wiring with screw terminal |
| Power supply load cells | 5 V dc / 120 mA (maximum 8 cells with 350 Ω in parallel) protected against short-circuit |
| Linearity | < 0.01% of full scale |
| Temperature deviation | <0,0003% of full scale/°C |
| Internal resolution | 24 bit |
| Weight resolution | Up to 60,000 divisions on useful capacity |
| Measuring range | From -1.5 mV/V to +3.5 mV/V |
| Weight acquisition frequency | 6 Hz – 25 Hz |
| Digital filter | 0,2 Hz – 25 Hz |
| Number of weight decimals | From 0 to 3 decimals |
| Logical output | 3 relays (changeover contact) maximum 115 V alternating current / 30 V direct current, 0.5 A each |
| Communication ports | RS232c / RS485 standard; 4-key remote control for configuration and operational commands |
| Max. cable length | 15 m (Rs232c), 1000 m (Rs422 + Rs485) |
| Serial protocols | ASCII + custom protocols |
| Baud rate | 1200 - 115000 bit/s, selectable |
| Options | External 868 MHz RF interface, Ethernet protocol, Profibus protocol |
| Conforms to standards | EN61000-6-2, EN6100-6-3, EN61010-1 |
For complete and up-to-date technical specifications please refer to the datasheet you can download here
Download PDF datasheet Connections
| Type | J1 5 poles serial female |
|---|---|
| Length | ND |
| 1 | GND + Shield |
| 2 | RS232 Rx |
| 3 | RS485 - |
| 4 | RS485 + |
| 5 | RS232 Tx |
| Type | J2 5 poles male load cell |
|---|---|
| Length | ND |
| 1 | + Exc. Load cell |
| 2 | + signal load cell |
| 3 | - Signal load cell |
| 4 | - Exc. Load cell |
| 5 | Shield |
| Type | J3 7 poles male optional outputs |
|---|---|
| Length | ND |
| 1 | Out 1 NA |
| 2 | Out 1 NC |
| 3 | Out 2 NA |
| 4 | Out 2 NC |
| 5 | Out 3 NA |
| 6 | Out 3 NC |
| 7 | Common output |
Load cell mounting
General guidelines for installing and mounting load cells:
- Respect the direction in which forces are applied to the load cells
- Do not exceed the temperature limits shown on the rating plate
- Do not remove the labels from the cells
- Protect cables properly with sheaths or cable ducts
- Connect each cell to earth with a suitable cable, bridging the plates of the mounting accessories if necessary
- Do not weld on the mechanical structure once the cells are in place
- Avoid or minimise mechanical constraints between the fixed structure and the weighed structure, to prevent weighing errors and zero return problems
- When vibrations or dynamic loads are present, protect the cells with anti-vibration mounts
- Protect the cells from dust build-up with suitable covers