Gicam weight indicators are weight indicator devices connected to load cells. We have multifunction displayers for weighing and dosing, for bridge weighing, with load limiter. Portable displayers are available in comfortable briefcases. We have panel mounting, portable, DIN and OMEGA bar mounts, analog indicators and touch screens indicators. IP65 products are available with dust protection. Gicam indicators support industrial communication protocols like PROFIBUS, PROFINET, MODBUS and more.

Indicator

Download usage manual


Zoom Click to enlarge image

Indicator WIN9

Technical Specifications

Power supply24 Vcc 15%
Max power consumption5 W
IsolationClass II
Installation CategoryCat. II
Operating temperature-10 / +40 C (85% humidity without condensation)
Storage temperature-20 / +50 C
DisplayNumeric 6 digit, 7 segments red LED's display (h 14 mm)
Led5 indicator leds (3 mm)
Keyboard4 mechanical keys
Overall dimensions96 mm x 48 mm x120 mm (l x h x p)
MountingPanel mount (cutout 91 mm x 44 mm)
Case materialSelfextinguish Noryl (UL 94 V1)
Protection levelIP 54
ConnectionsTerminal blocks, pitch 5.08 mm
Power supply load cells5 Vcc / 90mA (max six 350 ohm parallel load cells) short circuit proof
Input sensitivity0.02 V min
Linearity< 0.01% full scale
Temperature deviation< 0.001% full scale / C
Internal resolution24 bit
Weight resolutionUp to 60,000 divisions on the load capacity
Measuring range-3.9 mV/V - +3.9 mV/V
Weight acquisition frequency6 Hz - 50 Hz
Digital filterfrom 0.1 Hz to 25 Hz selectable
Number of weight decimalsfrom 0 to 3 decimal digit
Zero / FS CalibrationAutomatic (data sheet calibration) or via keyboard
Analog output in tensionOptional: 10 V / 5 V
 Resolution16 bits
 CalibrationBy push-buttons
 Impedance10Kohm Min
 Linearity0.03% full scale
 Temperature deviation0.001% full scale / C
Analog output under currentOptional: 0 - 20 mA / 4 - 20 mA
 Resolution16 bits
 CalibrationBy push-buttons
 Impedance300 ohm max
 Linearity0.03% full scale
 Temperature deviation0.001% full scale / C
Logical output2 opto-isolated max 24Vdc / 60 mA each
Logical input2 opto-isolated 24Vcc PNP (requires external power supply)
Serial portRs232c / Rs422 / Rs485 half duplex
 Max. cable length15m (Rs232c) and 1000m (Rs422 and Rs485)
 Serial protocolsASCII, Modbus
 Baud rate2400 / 9600 / 19200 / 38400 / 115000
Program code memory64 Kbytes FLASH on board reprogrammable by RS232
Data memory2 Kbytes
Conforms to standardsEN50081-1, EN50082-2, EN61010-1
For the complete and latest technical specifications, please refer to the technical data sheet which can be downloaded here:
Download PDF

Connections

TypeTerminal block 12P (pitch 5.08)
LengthND
1+ 24 Vcc Power supply
2- 24 Vcc Power supply
3Analog current output 0-20mA/4-20mA Max 300 ohm
4Analog vltage output 0-5V/ 0-10V min 10Kohm
5Negative analog output Voltage/Current
6RS232 Tx
7RS232 Rx
8GND
9RS485 TX+
10RS485 TX-
11RS485 RX+
12RS485 RX-
TypeTerminal block 12P (pitch 5.08)
LengthND
13Output 1
14Output 2
15Common output
16+ Input 1
17+ Input 2
18Common input
19- Exc. Load cell
20+ Exc. Load cell
21+ Load cell Sense
22- Load cell Sense
23- Signal load cell
24+ signal load cell
Connections  Indicator WIN9

MOUNTING OF THE LOAD CELL

General precautions to be followed in the installation and assembly of load cells:

  • Follow the direction of application of force on the load cell
  • Do not exceed the limits of the temperature as indicated in the data sheet
  • Do not remove labels from the load cell
  • Adequately protect the cables with sleeves or channels
  • Carry out on each load cell a ground connection with suitable cable, shunt on mounting accessories
  • Do not carry out any welding on the mechanical structure after mounting the load cell
  • Avoid or reduce to a minimum level any mechanical constraints between the rigid structure and the weighing structure to avoid error in weighing and return to zero
  • In case of vibration or dynamic loads product the load cells with puffers / shock absorbers
  • Protect load cell from any dust accumulation with any appropriate means