Indicator WIN TS


Download PDF

TOUCH SCREEN INDICATOR

LCD 5.2" graphic touch screen, high-contrast monochrome. Double channel input for load cells, incremental encoder input, dual analog outlet and additional analog input. Equipped with 6 digital inputs and 6 digital outputs, expandable with external modules.

On-board communication interfaces: RS232, RS485, USB, Ethernet, Modbus and Profibus DP. Optional USB Host port, for USB flash drives for data recording, uploading files and customizations.

Download installation manual

Download usage manual


Zoom Click to enlarge image

Indicator WIN TS

Technical Specifications

Power supply24 V cc 15 %
Max power consumption10 W
Installation CategoryCat. II
Operating temperature-10 / +50 C (14 / 122 F) Humidity Maximum 85% non-condensing
Storage temperature-20 / +60C (-4 / +140F)
DisplayLCD 5.2
 Display brightnessBacklight White LEDs, adjustable intensity
 Touch screenResistive 4 wires, suitable for use with gloves, buzzer
Drilling template187 x 97 mm / 7.36 x 3.82 in (l x h)
Overall dimensions196 x 105 mm / 7.72 x 4.13 in (l x h)
MountingRecessed in front panel
Protection levelIP 65
ConnectionsRemovable screw terminal block 5.08 / 7.5 mm pitch USB standard connectors ( Host / Device ) RJ45 Ethernet standard connector
Load cell input features2 input channels for load cells. Acquisition alternative or simultaneous at reduced frequency
Power supply load cells5 V dc / 120 mA (maximum 8 cells with 350 Ω in parallel) protected against short-circuit
Input sensitivity0.02 V min
Linearity< 0.01% full scale
Temperature deviation<0,0003% of full scale/C
Internal resolution24 bit
Weight resolutionUp to 600.000 scale intervals on scale capacity
Measuring range-7.8 mV/V - +7.8 mV/V
Weight acquisition frequency12.5 Hz - 250 Hz
Digital filter0.2 Hz - 50 Hz
Communication ports3 independent communication ports (not switched)
 Max. cable length15 m (Rs232), 1000 m (Rs485)
 Serial protocolsTCP/IP, UDP, ARP, ICMP, ModBus/TCP
 Baud rateDa 1200 a 115200 bit/sec
 OptionsUSB flash drive interface with FAT16 / FAT32 file system management
Micro-controllerRISC 32 bit, 44 MHz
Program code memoryFlash 256K Bytes, on-board upgradable (Rs232, USB)
Data memory1088 KBytes standards, expandable up to 2113 KBytes
Calendar clockIntegrated w/rechargeable battery
For the complete and latest technical specifications, please refer to the technical data sheet which can be downloaded here:
Download PDF

Connections

TypeTop Terminal block pitch 5.08 mm
LengthND
1RS232 Tx COM2
2RS232 Rx COM2
3GND
4RS232 Tx PRINT
5RS232 CTS
6TX+/RX+ RS485 COM2
7TX-/RX- RS485 COM2
8TX+ RS422 COM1
9TX- RS422 COM1
10RX+ RS422 COM1
11RX- RS422 COM1
12Out analog. 1 mA
13Out analog. 1 V
14Out analog 1 GND
15Out analog. 2 mA
16Out analog. 2 V
17Out analog 2 GND
18In analog. Volt
19In analog. GND
20Encoder power
21Encoder GND
22Encoder Phase A
23Encoder Phase B
TypeBottom Terminal block pitch 5.08 mm
LengthND
1- Exc. Load cell
2+ Exc. Load cell
3+ Ref. Load cell
4- Ref. Load cell
5Load cell 1, signal -
6Load cell 1, signal +
7Load cell 2, signal +
8Load Cell 2, signal -
9Input 1
10Input 2
11Input 3
12Input 4
13Input 5
14Input 6
15Common input
16Output 1
17Output 2
18Output 3
19Output 4
20Output 5
21Output 6
22Common output
TypeBottom Terminal block pitch 7.5 mm
LengthND
23Power supply 24 Vdc
24GND
Connections  Indicator WIN TS

MOUNTING OF THE LOAD CELL

General precautions to be followed in the installation and assembly of load cells:

  • Follow the direction of application of force on the load cell
  • Do not exceed the limits of the temperature as indicated in the data sheet
  • Do not remove labels from the load cell
  • Adequately protect the cables with sleeves or channels
  • Carry out on each load cell a ground connection with suitable cable, shunt on mounting accessories
  • Do not carry out any welding on the mechanical structure after mounting the load cell
  • Avoid or reduce to a minimum level any mechanical constraints between the rigid structure and the weighing structure to avoid error in weighing and return to zero
  • In case of vibration or dynamic loads product the load cells with puffers / shock absorbers
  • Protect load cell from any dust accumulation with any appropriate means